Meanwell Single, Bipolar and Triple Output Switching Power Supplies for Audio Projects

Construction information for DIY projects, including the MS Mid Side Matrix, Elliptic Equalizer, Mastering Console, Phono Transfer System, Insert Switcher and the Dual Class-A Amplifier. You can post your baby pictures here.
emrr
Posts: 528
Joined: Sun Mar 02, 2008 11:27 pm
Location: NC, USA
Contact:

Re: Meanwell Single, Bipolar and Triple Output Switching Power Supplies for Audio Projects

Post by emrr » Sat Feb 13, 2021 3:48 pm

Further tests are showing the 13k5 and 19k2 bumps to be environmental. Perhaps the 240 you see is too.
Best,

Doug Williams
Electromagnetic Radiation Recorders

User avatar
mediatechnology
Posts: 4951
Joined: Sat Aug 11, 2007 2:34 pm
Location: Oak Cliff, Texas
Contact:

Meanwell LRS-50-24 24V 50W For Insert Switcher Relay Supplies

Post by mediatechnology » Wed Nov 03, 2021 7:17 am

Wanted to add the Meanwell 24V 50W supply for Insert Switcher builds.

https://www.mouser.com/ProductDetail/709-LRS50-24

Fragletrollet
Posts: 8
Joined: Sat Oct 31, 2020 9:55 am

Re: Meanwell Single, Bipolar and Triple Output Switching Power Supplies for Audio Projects

Post by Fragletrollet » Tue Nov 16, 2021 1:56 am

Hello!

Planning a console build using 2x IGFO, 4x insert switcher, 1xMSII and 1xEEQ. Browsing options from MeanWell, how many amps are needed for these boards? Are the mA stated in the build docs (for all except the Insert Switcher) with all relays energized, aka total draw?
I know my additional LED's, meters & illuminated buttons will have to be added. Something like RS-50-25 or LRS-75-24 for the relays/led's, and a couple of RS 1515 or LRS 2515 for the bipolar 15v rails (I presume this works with these supplies, aka psu1 V+ = 15V, psu1 V-=0V, psu2 V+=0V and psu2 V-=-15V. I see that V- is connected to main earth, but through caps and other parts so I'm thinking it would be OK to connect it like explained?) or RS2524's for bipolar +/-18V?

I see RS has a little lower ripple than LRS, so I should choose RS?

Or maybe go for a RT-65C instead (is 0.5 enough Amps on the negative 15v?)?

I don't have much experience with SMPS, but was thinking to run these into something like a couple of TREX (TIP122/126 + caps & trimmer) for some conditioning of the bipolar audio rails between the supply and boards.

How does this all compare to just getting a suitable dual tapped 15V trafo and running it into a linear supply?


Thanks for any input and all the best,

Magnus

User avatar
mediatechnology
Posts: 4951
Joined: Sat Aug 11, 2007 2:34 pm
Location: Oak Cliff, Texas
Contact:

Re: Meanwell Single, Bipolar and Triple Output Switching Power Supplies for Audio Projects

Post by mediatechnology » Tue Nov 16, 2021 5:36 am

Magnus -

The currents given in the build documents are for the bipolar rails only.

I would highly recommend the TDK CUT35-5FF for the audio supply.
Mouser's delivery is in May of 2022 but Digi-Key have them. https://www.digikey.com/en/products/det ... FF/6874071
The /A and /B versions are the cover and base plate versions.
https://product.tdk.com/en/system/files ... ut35_e.pdf

Don't forget to buy JST connectors and pins. They are in the BOM for the TDK post. viewtopic.php?f=7&t=945

The 1A (+) and 0.65A (-) capability will offer plenty of extra current.

Your boards use 24V relays for everything except the Insert Switcher which use 12V relays in series for a 24V coil.
The 24V Omron relays in the BOM pull about 8.3mA each.
Add 10 mA for each LED.

The Insert Switcher relays are 12V. In Omron the current is 12.5 mA.
There are 14 relays on each board but because they are in series they count as 7 at 12.3 mA.
Add 3 LEDs (max) per board at 10 mA.
For 4X insert boards with all relays engaged you're looking at about 0.46A.

Based on the number of boards it look like they relay supply will need about 750 mA or 18W.
I'd use the 50W Meanwell which will give you quite a bit of extra headroom though you could use a 25W if you needed too.

Post Reply